FUTABA 12Z MANUAL PDF

Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Yozshujas Dut
Country: Philippines
Language: English (Spanish)
Genre: Music
Published (Last): 1 October 2009
Pages: 381
PDF File Size: 16.66 Mb
ePub File Size: 10.61 Mb
ISBN: 962-3-43932-265-2
Downloads: 27684
Price: Free* [*Free Regsitration Required]
Uploader: Nihn

Remember, if the predefined control suddenly This function only works with G3 or PCM receivers moves to a position you did not command, land at Futabz types, all settings will be lost. Mixing rate setting procedure The HR-3 is taken as an example to describe mixing rate setting.

Page 74 be used for each condition. Setting of these 2 positions can be selected by switch. A needle curve can be set.

Page 16 Adjustment of the stick lever length Adjustment of Throttle Stick Ratchet System You can also choose either airplane ratchet system or helicopter-touch. The differential rate can also be adjusted according to the flying state by Note: Rutaba a description of the curve setting method, see the description at the back of this manual.

The servos operate smoothly at a side and return OUT side can also be set by servo speed setting 1 function. To add new models or to call a model already set, manuwl the Model Select function of the Linkage Menu.

Operation modes Symmetrical box mode The operation modes when stick, trim lever, or but left and right up and down operation is knob was selected are described below. Danger Do not connect any other chargers except CR to this charging connector.

Use the Function menu of the Linkage Menu to assign the sensitivity is used to stabilize the aircraft’s attitude. Model futabs Select the model type f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider. Enter text from picture: The action is not functional at high throttle to avoid accidental dead sticks.

When you select model and wing swash 12.

  EMERITA BRASILIENSIS PDF

Page 72 which can be switched by switch, etc. Lever Head Lever Head 1.

After the set mode is changed from group mode [GROUP] to single mode [SINGL] at the control selection screen, only that condition setting is changed by control change; setting of other conditions remains the same. Mixing applied in other swash modes is different, but the setting procedure is the same. Two independent timers are provided for your use. Curve setting examples actually creating a curve, enter the data specified The curves shown below were created by using per the aircraft or the reference value.

If you would like, you can freely change combinations of servo output channels, functions aileron, elevator, etcand input controllers sticks, switches, trim levers and trim switches.

Futaba 12Z User Manual | pages

Ailevator is where each elevator in a standard conventional or v-tail moves independently, like ailerons on a wing. The method of applying the curve setup screen, and then correct the sinking.

Page Operation modes Symmetrical box mode The operation modes when stick, trim lever, or but left and right up and down operation is knob was selected are described below. Page 43 Receiver and servo connection Connect the receiver and servos in accordance with the connection diagram shown below. Page Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1.

In order for you to make the best use of your system and to fly safely, please read this manual carefully. For a description of the switch setting method, see the description at the back of this manual. For PPM mode, you can set only eight linear channels. The operation speed can be set in 2 ranges of slow speed flight and high speed operated as a safety function by setting 2 switches.

When to PPM mode. Adjustment to the curve you want to use is possible by using the 12Z’s powerful Curve Edit Function. Up to 8 and other functions common to all model types. Helicopter basic setting procedure etc.

  BC142 DATASHEET PDF

The display screen is an example. Display adjustment and auto power off setting. Model addition and call Default setting assigns 1 model to the T12Z. Flight condition’s addition, deletion, copy, condition renaming, and condition delay can be set. Page 53 Model type Select the model type f r o m a m o n g a i r p l a n ehelicopter, glider, and motor glider. Unfortunately a number of Futaba requests remain incomplete due to a shortage of parts.

Futaba 12Z User Manual

Never hold the antenna alone. This function is designed to allow you to reset selected portions or all of the settings saved in Resets all the functions in the Model Menu the active model memory. The screen depends on the model type. Page Switch selection method lever, or VR are used as a switch setting method is common to all functions. Adjustment of the stick lever length Adjustment of Throttle Stick Ratchet System You can also choose either airplane ratchet system or helicopter-touch.

Setting method turn the data input dial to the left and push the enter The rate and curve of each servo can be set by calling each screen. Equipment for reading and writing CF cards are available at most electronics stores.

FUTABA 12Z Series Manuals

It can be used to bank scale models, large models, etc. Receiver and servos connection diagram Ni-Cd battery Receiver switch Page Operations related to servo speed Servo speed setting 1 Servo speed setting 2 The servo speed at each function operation including flight condition switching can be The operation start point at operation IN adjusted.

The servo speed can also be adjusted. Page 39 Helicopter basic setting procedure etc. It is used when rudder is applied during roll maneuvers, knife edge, etc.

iPhone X